Lightning VME En

Aus Atari Wiki
Wechseln zu: Navigation, Suche

General

The Lightning VME is an internal plug-in card that extends the Atari TT and the Mega STE with two USB 1.1 compatible interfaces.


Features

  • new developed in 2018 (Pakman, Tuxie, Czietz, Gaga)
  • two USB 1.1 interfaces, expandable by USB-hub
  • both ports can be used simultaneously
  • no external power supply necessary
  • even USB 2.0 devices work, but then at a reduced speed
  • currently ca. 600kb/s transfer rate in unaccelerated TT
  • also works in accelerated TT, thus further increase in performance (tested with 20MHz bus and 40MHz CPU)
  • Transferrate is customizable
  • compact design, fits in the original case of both the MegaSTE and the TT
  • plug and play - fully pluggable solution
  • central elements are a programmable Logic Device (CPLD) from Xilinx and the ISP1160 USB-Host-Controller from Philips
  • handmade, SMD in reflow process
  • triple protection of both USB ports:
    • electrostatic discharge (ESD) protection when connecting external devices
    • overcurrent protection by self-healing fuses
    • secured against twisting the USB bracket by coding and labeling
  • other interfaces, ROM port, ACSI interface and VME slot remain free
  • support real USB mice, not only with PS/2 protocol
  • finally true support of mass storage even under TOS
  • works under TOS 2.06 and 3.06, Magic 5.x and Mint
  • only occupies the address range 0xFEFF8000 - 0xFEFF8009 of the VME bus in the TT
  • especially suitable in combination with Thunder IDE Interface and / or Storm

Description

Lightning vorn.JPG Lightning hinten.JPG

The Lightning is designed so that no soldering is required; it´s is plug and play.

It disappears completely inside the original case.

Currently drivers for mass storage, mice and USB2LAN devices are available. Extensions by new drivers are possible, e.g. USB keyboard or USB floppy.

Now it´s possible to use:

  • USB mice
  • USB memory sticks
  • USB card readers (SD, CF etc.)
  • USB2LAN (with Asix 88772 chipset)
  • USB CD / DVD drive (note current limitation and installation of ExtenDOS / MetaDOS required)
  • USB keyboard (in planning)
  • etc.

This finally enables the use of up-to-date hardware as well as the simplest data exchange in the world of Windows or OSX.

Hardwarerevisions and Firmware

As of 17.02.2018, the hardware revisions B with firmware 04 are up to date.



Hardware installation

The installation of the Lightning VME in the TT is very easy. Please follow the instructions below.

The card fits in all 3 known motherboard versions of the TT:

  • Daughterboard - CPU (plugged)
  • PGA CPU (plugged)
  • SMD CPU (soldered on) - this version is particularly well suited for easy installation.

The Lightning VME harmonized well with the Thunder IDE Interface and the Storm. The cards are not hindering each other.

There is a small possibility that after installation of the Lightning VME your existing TT-RAM extension does not physically fit into the TT.

This applies, for example, to the original FAST RAM extension card from Atari (1/4/16 MB).

Then it's time to swap them for a [Storm] (up to 256 MB).

21 TT Lightning Lieferumfang.jpg

Delivery.


01 TT geschlossen.jpg

The computer in the closed state, here a little bit yellowed version.

Do not forget: all works without electricity!


02 TT Oberteil ab.jpg

After loosening the screws on the underside, carefully fold up the upper shell.

Carefully remove the two front ribbon cables from the backplane of the VME board.

The VME backplane is held by the metal cage.

It is not mandatory to remove the metal cage and / or the backplane.


03 TT Urzustand rechts.jpg

View after opening the TT, looking at the VME backplane and the VME metal cage.


04 TT Urzustand VMEKabel ab.jpg

Here are the ribbon cables removed. That's half done!


05 TT Urzustand Backplane nah1.jpg

Here is a close-up.

It is a TT with SMD CPU.

There is a lot of space for the installation of the Lightning.

The cabling is factory patches from Atari.

Soldering to install the Lightning VME is not required.


06 TT Urzustand Backplane nah2.jpg

Another close-up. The TT is ready to plug in the Lightning VME now.


07 TT Lightning nicht aufgesteckt1.jpg

Gently bring the Lightning VME to the backplane. Page and direction are self-explanatory.

If you are sitting in front of the TT, you should be able to read on the top left "Atari VME-USB Adapter Rev. B" and the CE sign and two yellow, angular components.


08 TT Lightning nicht aufgesteckt2.jpg

Ensure correct position! No backplane pins should be visible.


09 TT Lightning aufgesteckt1.jpg

Then gently and evenly press the Lightning VME against the backplane with moderate force.

Remember: may force be with you, young padawan!


10 TT Lightning aufgesteckt2.jpg

By the way: please do not use the now visible, angled pins, do not connect either, otherwise there is a risk of damage.

The pins are exclusively for service (uploading the firmware).


11 TT Lightning1.jpg

That is exactly how it should look.

The TT now has 2 USB ports on the right side towards the internal hard drive / ST-RAM.


12 TT Lightning2.jpg 13 TT Lightning3.jpg

Seen from left and right.


14 TT Lightning4.jpg

Here you can see that the Lightning VME is parallel to the VME backplane, but without touching it at the top.


15 TT USB nah1.jpg

Closeup of the USB pins, divided into port 1 and 2.

There is no pen on the bottom left - this is the encoding for the USB bracket.


16 TT Lightning nah2.jpg

Plug of the USB bracket.


17 Lightning drin1.jpg

Nice to look at, right?


18 TT Lightning drin2.jpg

Here with closed top, but missing the so called "lunch box".

The bracket can be installed as desired, e.g. to the rear.

How about connecting a Teac FD-CR7 internally to one of the USB ports?


19 TT Lightning drin3.jpg


20 TT Lightning drin4.jpg

Of course, the lunch box fits on it again, even with a hard drive.


21 TT Lightning drin5.jpg

Custom work.


Lightning Daughterboard1.jpg

The picture shows the Lightning VME in a Daughterboard TT.


When everything is installed and screwed together, only the software has to be installed.



Software installation

The enclosed floppy disk contains the driver software for TOS / Magic and Mint as well as instructions in text form.

It is divided for Atari TT and Atari Mega STE as follows:


Inhalt Diskette.jpg

Caution: Do not swap: TT drivers do not run in MSTE and MSTE drivers do not run in TT.



Configuration, meanings and contexts

loader.prg (just for Mint)

The Loader is a utility that loads the USB stack and integrates it into the system.


usb.prg / usbxxx.km

This file is the USB stack that makes USB possible at the Atari.

The USB stack manages the USB bus and the devices connected to it.

It provides the necessary basic functions to the following drivers.


storage.prg und mouse.prg / storage.udd und mouse.udd

These drivers are based on the USB stack and communicate with the connected devices, such as a USB stick (storage) or a USB mouse (mouse).

These drivers can be extended as required, depending on availability.

Thus eth.prg (already existing) or a keyboard.prg (planned) can provide the possibility of a network interface and a USB keyboard.


blitz0x0.prg / blitzxxx.ucd

This file is the link between the USB stack and the Lightning VME.

It allows communication between the USB stack and the Lightning VME card.


usb.acc

This ACC under TOS and Magic ensures that the USB bus is hotplug capable.

It therefore detects whether new devices have been connected and integrates them into the system.

Of course, it also shows which devices are currently connected.


additional note on ExtenDOS / MetaDOS in case of using a USB CD drive:

This must be loaded after storage.prg.

The USB driver provides an interface according to the SCSIDRV standard, which can be used directly with ExtenDOS.

In the case of MetaDOS, a driver such as SPIN needed by Julian F. Reschke.


TOS and Magic

Here, the contents of the floppy's Auto folder are simply copied to the boot folder's Auto folder.

Attention: the correct order when copying or booting is essential!


Use this bootorder under TOS:

  • USB.PRG
  • MOUSE.PRG
  • STORAGE.PRG
  • BLITZ030.PRG


In case of using Magic, Magic has to be loaded before of the USB programs:

  • MAGXBOOT.PRG
  • USB.PRG
  • MOUSE.PRG
  • STORAGE.PRG
  • BLITZ030.PRG


Hints:

  • a possible bootloader always comes first.
  • any additional, optional USB device drivers (ETH.PRG) will come after STORAGE.PRG / before BLITZ030.PRG
  • BIGDOS.PRG comes as the first program after the bootloader, in any case [before] MOUSE.PRG


Here's an example of a working order:

TT Startprogramme.jpg Bootorder.JPG


If everything works correctly, it looks like this under TOS 3.06 (here with Nova Mach32):

Lightning TOS2.jpg

You can see that the USB.ACC has found the Lightning as Root Hub as well as an optical USB mouse and a USB stick.


TT Lightning Hddriver1.JPG

USB mass storage devices detected by the system can be set up as usual, here using the example of the HDDriver 10.10.


TT Lightning Hddriver2.JPG

The same restrictions apply as for other drives.



Mint

The installation under Mint is also not difficult.


  • Step 1:

The drivers are not loaded from the Auto folder, but via the loader.prg from the USB directory under Mint.

For this, copy all files from the directory a:\tt\mint from the floppy disk to

C:\mint\1-19-cur\usb

If the USB directory does not exist, it must be created.


  • Step 2:

In the next step, the file mint.cnf, which is located at c:\mint\1-19-cur\, must be adapted.

To do this, open this file with an editor (for example, QED, Luna, etc.).

Pretty much at the end of mint.cfg there is a line called:

GEM=u:/c/mint/1-19-CUR/xaaes/xaloader.prg

The following must be inserted before this line

exec u:/c/mint/1-19-cur/usb/loader.prg

The CUR may need to be replaced by its existing kernel version number.


Lightning Mint1.jpg

When starting Mint, the Driver should bring about these issues.


TT Lightning Mint2.jpg


Then the USB devices are also available under Mint, here the example of MyAES Desktop.



USB2LAN

Note: the following entries are updated continuously.


The following USB network adapters work with the Lightning (driver for Mint):


  • DLink
    • DUB-E100, silver, H / W Ver. B1
    • DUB-E100, black, H / W Ver. C1


  • " China-adapter" with ASIX chipset
    • AX88772A
    • AX88772B


Attention: Currently there are USB2LAN adapters for small money (quite small and white housing). Often a different network chip is installed, as it is on offer.

If the name AX88772 stands directly on the device, there is a high probability that this chip is actually installed.


Notes on software installation:

1. ETH.UDD must be in USB folder and ASIX.XIF in MiNT main folder.

2. The device is called "asx0".

3. It is configured like any other network card under MiNT, ie with ifconfig, route, etc. pp.



Lightning VME in interaction with other VME cards

Please follow this link and use a translator:

Lightning VME USB Interface

Scroll there to the very end of the post.



last update: 06.03.2018 (Gaga)